Double hung
Single hung
Horizontal roller
Casement
Bay & bow
Sliding glass doors
Entry doors
Impact garage doors
PGT
CGIFree in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Get your free estimateStyles & brands we work with
- Single hung
- Double hung
- Horizontal roller
- Casement
- Bay & bow
- Sliding glass doors
- Entry doors
- Impact garage doors
- PGT
- CGI
See the difference
Before
After
Before
After
Before
AfterFrench & Double Doors in Enterprise, NV
A French door is a hinged door with glass lites running the full height of the panel, usually hung as a matched pair so both leaves swing open. A double door is the same two-leaf idea in a solid or paneled configuration. Either one turns a dark hallway into a room that borrows light from the patio, and either one fails the same way when it’s hung out of square: the active leaf drags, the weatherstripping gaps in July, and the glass fogs at the seal within a few summers. If you’re replacing or adding one in Enterprise, call (844) 629-7617 and a live person picks up, day or night.
We install French and double doors across the southwest valley, from the older single-story tracts off Windmill to the newer builds near Mountain’s Edge and the Southern Highlands foothills. The work sits under our broader Door Installation in Enterprise service, and it’s the part of that service where measuring twice matters most – a double opening has no fudge room. A quarter inch of error on a single door is a shim. On a pair, it’s a binding door in August.
When You Need French & Double Doors
Most of the calls we take for French and double doors aren’t new construction. They’re replacements, upgrades, and repairs on openings that have been in the house since it was built. Here’s what homeowners in Enterprise describe when they call us:
- The door binds or drags as the desert heats up. Stucco and wood framing move with temperature swings, and a pair that swung clean in March catches on the threshold by July. If you’ve been lifting the door to close it, the frame or the hinge side has moved, and re-hanging it properly is usually cheaper than replacing it.
- The sealed glass unit has gone cloudy. This is the single most common failure we see on French doors in Enterprise. The dual-pane unit loses its perimeter seal, moisture gets in, and the glass hazes from the edges inward. On a double door that’s two panes, and the fix is a glass swap, not a whole new door.
- You want more light into a back room. A solid double door on a family room or primary bedroom blocks the light and the view. Swapping it for a French pair with tempered glass adds daylight without adding a window.
- You’re opening up to a patio or covered lanai. A hinged French pair that swings out to a covered patio is a common upgrade here, especially on homes with a walled back yard where a slider doesn’t quite work.
- The old door leaks dust and hot air. In the spring wind season, a door with worn weatherstripping and a bad sill gasket lets fine dust in along the bottom edge. You’ll see a line of grit on the tile every morning. New thresholds and sweeps solve most of it.
- The lock or the astragal has failed on one leaf. The astragal is the vertical strip where the two doors meet. When it wears out or the flush bolt stops catching, the inactive leaf rattles and the door won’t seal. That’s a hardware and adjustment job, and it’s one we handle on a single visit.
Our French & Double Doors Process
Every opening gets the same sequence, whether it’s a straightforward swap or a custom pair going into a wall that’s never had a door. Our technicians have up to 18 years of experience on door and window work, and they work to the founding rule the company was built on: if the pane is not true, the job is not done.
- Measure the rough opening twice, then check it against the frame. We check plumb, level, and square on the opening, not just the width and height. On a double door the diagonal measurements matter most – if the opening is out of square, we address that before the new unit goes in, because a pair hung into a crooked opening will never swing right.
- Quote the manufacturer lines side by side, on paper. We’re an authorized installer for more than a dozen lines, including Therma-Tru and ES Windows, and we put the options in front of you so you can see exactly what each one costs and what each one includes. No verbal-only estimates, no surprise line items.
- Remove the old unit and inspect what’s behind it. We check the framing and the sill pan for water damage or rot before we set the new door. If the rough sill needs repair, we tell you before we proceed, not after.
- Set, shim, and fasten the new frame true. The door goes in plumb and square, shimmed at the hinge points and the strike side, and fastened per the manufacturer’s spec. We set the hinges and strike plates so both leaves close with even reveal – the gap between door and frame should be uniform top to bottom.
- Weatherstrip, seal, and test the swing. New thresholds and sweeps go in, we check the astragal engagement, and we open and close both leaves several times. Then we check the lock and the flush bolts. If a leaf binds anywhere in its arc, it gets adjusted before we call the job done.
- Register both warranty layers before we leave. This is The Keystone Standard. The manufacturer’s product warranty and the installation warranty both get registered in writing, with durations stated, before the truck leaves the driveway. That’s the piece most installers skip, and it’s the piece that matters when a seal fails or a hinge backs out in year four.
Most French and double door replacements happen in a single visit. Custom pairs or openings that need framing work may run longer, and we’ll tell you the schedule up front so nothing gets left hanging.
French & Double Doors Pricing in Enterprise
French and double door pricing in Enterprise depends on the size of the opening, the material, the number of glass lites, and whether the existing frame stays or comes out. These are honest ranges to plan by. Your exact number comes from a free on-site estimate, because a door we can’t see is a guess.
| Scope | Typical Range |
|---|---|
| Single French door, standard size, installed | $1,400 – $3,200 |
| Double French door pair, standard size, installed | $2,600 – $5,800 |
| Custom or oversized double door with framing changes | $5,000 – $9,500+ |
| Glass unit (IGU) swap on existing French door, per pane | $350 – $700 |
| Hardware, astragal, and adjustment repair | $150 – $450 |
What moves the number: the glass package (tempered, low-E, and impact-rated units each cost more), the material of the door (fiberglass and steel cost more than wood-clad), the number of lites, and whether we’re working with the existing frame or replacing the full opening. A door in a masonry wall takes more time than one in a wood-framed wall. If you need impact-rated glass for a specific opening, the glass cost climbs noticeably – but it’s a one-time cost on a door you’ll keep for decades, and we’ll put the number in writing before you commit.
We don’t win jobs by being the cheapest bid in the room. We win them by measuring twice, quoting on paper, and standing behind the work. Free on-site estimate, upfront pricing, and a standing $50 Off Any Repair Over $250 if you’re booking a repair rather than a replacement. Seniors and veterans get a permanent 5% discount, and there’s always our $89 Seasonal Tune-Up for doors that just need adjusting and resealing. Call (844) 629-7617 to schedule.
FAQs – French & Double Doors
How much do French doors cost to install in Enterprise, NV?
French door installation in Enterprise typically runs $1,400 – $3,200 for a single door and $2,600 – $5,800 for a matched double pair, installed. Custom sizes and openings that need framing changes go higher. The fastest way to a real number is a free on-site estimate – call (844) 629-7617 and we’ll come measure and quote on paper.
Can you fix fogged glass on a French door without replacing the door?
Yes, in most cases. If the door frame and hinges are sound and only the sealed glass unit has failed, we swap the pane for $350 – $700 per pane and keep the door. It’s a same-visit job on most French doors. Call (844) 629-7617 for a free estimate and we’ll tell you honestly whether the glass or the whole door is the right call.
Do you install impact-rated French and double doors?
Yes. We install impact-rated French and double doors for homeowners who want that protection, and we’re an authorized installer for lines including ES Windows and Therma-Tru that offer impact-rated units. Impact glass adds to the cost but is a permanent upgrade to the opening. Call (844) 629-7617 and we’ll quote the impact and non-impact options side by side.
Can you install French doors into a wall that doesn’t currently have a door?
Yes. Opening a new doorway for a French or double door is a job we take on, and it’s the one that most needs careful measuring and a proper header. It takes more than a single visit because the framing, header, and finish work all need to be right. Call (844) 629-7617 for a free estimate and a realistic schedule.
Is a French door a good choice for a back patio in Enterprise?
Yes, if the patio is covered and you want the light and the swing. A hinged French pair out to a covered lanai is a common and durable choice here. On an uncovered patio, a door that takes direct sun and rain wears faster, so we’ll talk through the exposure before you choose. Call (844) 629-7617 and we’ll walk the opening with you.
What warranty comes with French and double door installation?
Every job is covered by the 90-Day Done Right Promise and The Keystone Standard: both manufacturer warranty layers registered in writing, with durations stated, before the truck leaves. If something’s not done right in the first 90 days, we make it right – no paperwork fight, no arguing. Call (844) 629-7617 to get started.
Ready to get your French or double door done right?
We’ve served local communities for over 42 years, we hire local and train apprentices into journeymen, and we plan to be in town in thirty years – which is why we register both warranty layers and answer the phone at 2 a.m. If a French or double door in your Enterprise home is binding, fogging, leaking, or ready for an upgrade, call TruePane Windows & Doors Enterprise at (844) 629-7617 for a free estimate. A live person answers every call, day or night, and we’ll be there when we say.
Written by the team at TruePane Windows & Doors Enterprise, serving Enterprise.