Impact garage doors
Single hung
Double hung
Horizontal roller
Casement
Bay & bow
Sliding glass doors
Entry doors
PGT
CGIFree in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Get your free estimateMr-Glass Impact Garage Doors: The Enterprise Owner’s Guide
We install and replace Mr-Glass-compatible impact garage doors in Enterprise, and a full single-car door with a hurricane-rated glass section typically runs $2,400 to $4,800 installed depending on size, glass package and frame finish. Most jobs are completed in a single visit once the door is on site and the opening is measured. Enterprise owners usually find us after one specific moment: a torsion spring snaps, the opener drags and stalls, or a section of laminated glass takes a hit and they realize the “impact” rating the door came with was the reason they bought it. That is when the questions start – which Mr-Glass model is this, what part matches it, and who in Enterprise will price it honestly instead of guessing.
Which Mr-Glass Models This Applies To
Mr-Glass builds its impact garage doors around sectional panel systems, and the part you need almost never crosses between door widths. A single-car door and a double-car door share a glass style but not a track radius, not a torsion spring wind, and not a hinge pattern. The data plate on the inside of the top or bottom section is your first stop: it carries the model designation and the door weight, and the weight is what determines the spring. If the plate is missing or painted over, we measure the panel thickness, the section height (Mr-Glass runs standard panel heights that don’t always match what a generic replacement assumes), and the track radius from the jamb line before we quote anything.
That brings up the OEM-versus-aftermarket decision, and it’s where Enterprise owners get burned. Mr-Glass glass panels are laminated impact units built to a specific thickness and interlayer spec – a generic 1/4-inch laminated panel of the same nominal size will fit the channel but won’t carry the same rating, and it may not sit flush in the extrusion. Springs, hinges and rollers are a different story: a matched aftermarket torsion spring or nylon roller of the correct wind and gauge does the same job at a lower price. We’ll tell you which is which on paper, side by side, and let you decide.
We are an independent service provider and are not affiliated with Mr-Glass. We also work with PGT, CGI and CWS impact products when a mixed brand situation comes up.
Styles & brands we work with
- Single hung
- Double hung
- Horizontal roller
- Casement
- Bay & bow
- Sliding glass doors
- Entry doors
- Impact garage doors
- PGT
- CGI
Signs Your Mr-Glass Impact Garage Doors Is Failing
Mr-Glass impact doors fail in a fairly predictable order, and the symptom usually points to one component:
- The door slams down or won’t stay open. A torsion or extension spring has lost tension or snapped. In Enterprise’s summer heat, a spring cycled a few times a day can let go anywhere between 7,000 and 10,000 cycles – and the day it fails, it fails loudly.
- A loud bang from above the door, then nothing works. Classic broken-spring signature. The door is now dead weight on the opener, which is not built to hold it. Stop using the opener until it’s looked at.
- The door binds, squeals, or jumps the track on one side. Worn nylon rollers, a bent hinge, or a track that has shifted. On an impact door the panels are heavier, so roller wear shows up faster than on a standard door.
- A crack, chip, or cloudy patch in the glass section. The laminated interlayer has been compromised or moisture has worked into the seal. An impact panel that’s cracked is no longer an impact panel.
- The opener strains or the door reverses halfway. Often a balance problem rather than an opener problem – the springs are tired and the motor is doing work it shouldn’t. Chasing the opener first is the most expensive mistake we see.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Installed pricing in Enterprise depends on the part and the door, but here is how it breaks down on a square deal – parts plus labor, no surprise line items:
| Work | Typical installed range |
|---|---|
| Torsion or extension spring replacement (pair, balanced) | $220 – $420 |
| Roller and hinge refresh (full door set) | $180 – $320 |
| Track realignment or section repair | $200 – $450 |
| Impact glass panel replacement (single section) | $450 – $1,100 |
| Full Mr-Glass-compatible impact door, single-car | $2,400 – $4,800 |
What moves the number: door width and weight, whether it’s a torsion or extension setup, and whether the glass panel is a matched impact unit. Every job carries our 90-Day Done Right Promise – if the door isn’t right, we make it right, in writing, no arguing. We quote manufacturer parts on paper before we start.
DIY or Call Us?
Some checks are safe and worth doing before you call. Confirm the data plate model, watch whether the door is balanced with the opener disconnected, look for a visible gap in the spring or a track that’s pulled away from the jamb, and note which side binds. That’s information we can use.
The rest – springs, cables, and anything under load – is where DIY goes wrong. A wound torsion spring stores enough energy to break a wrist or worse, and an impact door’s heavier panels make the stakes higher. We don’t hand out spring-replacement steps, and no honest glazier will. Leave the high-tension work to a trained technician. Call (844) 629-7617 and we’ll schedule a free estimate on the part and the balance of the door.
FAQs
How long do Mr-Glass impact garage door parts last in Enterprise? Springs typically run 7,000 to 10,000 cycles; rollers and hinges last longer but wear faster in our dry, hot climate. Enterprise’s spring and fall temperature swings are hard on springs, so a door cycled four times a day can need a spring well before the door itself shows age. Call (844) 629-7617 for an exact quote – estimates are free.
Can the part be repaired instead of replaced? Sometimes. A worn roller or a slightly bent hinge is a repair; a snapped spring or a cracked impact glass panel is a replacement. We’ll tell you which on paper before any work starts.
How long does the swap take? A spring or roller job is usually done in a single visit, often under two hours. A glass panel or full door replacement takes longer and we’ll give you a clear window when we quote.
How do you source the Mr-Glass part? From the model and weight on the data plate, matched to the door’s actual measurements. We don’t carry parts on a truck and won’t guess at a fit – the part is ordered to spec, quoted on paper, and registered before we leave. Call (844) 629-7617 to get started.
Mr-Glass impact garage doors in Enterprise deserve a part that matches the door and a technician who measures twice. Whether it’s a snapped spring, a failing roller set, or a compromised impact panel, we’ll price it honestly and stand behind the work. Call (844) 629-7617 for a free estimate on your Mr-Glass impact garage door in Enterprise – a live person answers, day or night.
Written by the team at TruePane Windows & Doors Enterprise, serving Enterprise and nearby areas.