Single hung
Double hung
Horizontal roller
Casement
Bay & bow
Sliding glass doors
Entry doors
Impact garage doors
PGT
CGIFree in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Get your free estimateCWS Door Installation: The Enterprise Owner’s Guide
If your CWS door is failing, the fix is almost never a full door replacement – it’s a correct door installation and hardware reset, and in Enterprise that typically runs $450 to $1,850 installed depending on door type, hardware, and whether the rough opening needs correction. Most CWS door problems we see in Enterprise show up as a door that drags the threshold by August, a latch that won’t catch without a shoulder push, or a bottom seal that’s worn through after a few summers of desert grit. Owners usually notice it as a scrape, a draft, or a light gap at the jamb corner before they realize the door has lost its true. We install and reset CWS doors with both warranty layers registered in writing before we leave, backed by our 90-Day Done Right Promise. Call (844) 629-7617 for a free estimate.
Which CWS Models This Applies To
CWS builds entry, patio, and interior doors across several product lines, and the parts that matter – hinges, locksets, multi-point hardware, thresholds, sweeps, and glass units – are not interchangeable across series. The most useful first step is finding the CWS model label, which is typically a sticker on the door edge, the top rail, or inside the frame head. Take a clear photo of it. If the label is gone, we measure the slab thickness, the rough opening, and the hinge pattern, and match those to the CWS series spec.
The decision between OEM and a quality aftermarket equivalent depends on the part. For a 5-pin cylinder or a perimeter seal, a good aftermarket unit performs identically and costs 30-40% less. For hinge sets on a multi-point CWS door, stay with OEM or a verified equivalent – the hinge positions are drilled for the original hardware and aftermarket hinge leaves usually need re-mortising, which is where most failed installs in Enterprise begin. On glass units, the sealed IGU has to match the original thickness and spacer; a substitute unit that’s 1/8″ off will not sit in the glazing pocket correctly and will fog early. CWS-compatible doesn’t mean CWS-approved, and we’ll tell you which side of that line each part lands on before you buy.
Styles & brands we work with
- Single hung
- Double hung
- Horizontal roller
- Casement
- Bay & bow
- Sliding glass doors
- Entry doors
- Impact garage doors
- PGT
- CGI
Signs Your CWS Door Installation Is Failing
These are the five symptoms we see on CWS doors in Enterprise, and what each one usually traces back to:
- Door drags the threshold in summer. Thermal expansion in the desert heat plus a hinge set that’s sagged a fraction. The strike plate is carrying weight it was never meant to bear.
- Latch won’t catch without a push or lift. The door has lost true at the hinge jamb, usually from hinge screws backing out in our drywall and stucco substrate. The lockset itself is often fine.
- Light gap at the top or lock-side corner. Frame has racked or the rough opening was never shimmed correctly on the original install. Common in doors set more than fifteen years ago.
- Bottom seal torn or flattened. Fine desert grit and caliche dust chew through a sweep faster than most owners expect – two to three years in a south-facing entry.
- Glass unit fogged between panes. The seal on the sealed IGU has failed, letting moisture in. Not a door problem; a glass unit replacement.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
CWS door installation work in Enterprise generally falls into these ranges. Everything is quoted line by line, on paper, before any work begins.
| Scope | Installed Range |
|---|---|
| Hardware reset and hinge replacement (entry door) | $180 – $420 |
| Lockset / multi-point hardware replacement | $220 – $650 |
| Threshold and sweep replacement | $150 – $380 |
| Sealed glass unit (IGU) replacement, standard size | $280 – $750 |
| Full door slab or unit replacement (CWS-compatible) | $950 – $1,850 |
What drives the range: door type, whether the rough opening needs correction, glass size and spec, and hardware line. Labor is quoted separately from parts so you see exactly what you’re paying for. Every job we complete carries the 90-Day Done Right Promise – if something isn’t right, we come back and make it right, no paperwork fight. Both manufacturer warranty layers are registered in writing before we leave the driveway, with durations stated.
DIY or Call Us?
An owner can safely check three things: the CWS model label (photograph it), whether the door sits square in the opening (close it slowly and watch for light gaps), and whether the hinge screws are tight (turn them by hand, don’t force them). Those checks tell you whether you’re looking at hardware or the door frame.
Where DIY goes wrong on a CWS door: adjusting the hinges to fix a sag, which throws the lockset alignment off and can crack the door skin; prying an IGU out of a glazing pocket without the right suction tools and spacer shims, which can crack the glass or break the seal on the new unit; and re-mortising a hinge leaf on a hollow-core slab, which usually ends with a hinge that holds for a season and then tears out. Every one of those repairs is done in a single visit on most doors. If you’re not sure, call us at (844) 629-7617 – a quick conversation tells you what you’re dealing with.
FAQs
A properly installed CWS entry door should give you 20 to 30 years on the door frame and slab, but hardware and seals wear far faster in our climate – bottom sweeps typically last two to three years, hinge sets six to ten. Glass units are the variable piece; a sealed IGU on a south- or west-facing door in Enterprise often fogs between year eight and year twelve because of the daily thermal swing. Call (844) 629-7617 for an exact quote on your door – estimates are free.
Yes, most of the time. A door that drags, doesn’t latch, or leaks light is almost always a hardware or hinge problem, not a door problem – and that’s a repair, not a replacement. We only recommend a new unit when the door slab or frame itself is warped, cracked, or water-damaged. Call (844) 629-7617 and we’ll tell you honestly which one you’re facing.
Hardware and hinge work is typically done in a single visit, most jobs finished in under three hours. A sealed glass unit swap on a standard door is usually a one-visit job as well. Full door replacements are scheduled separately and usually take a full day. Either way, you’ll know the timing before we start. Call (844) 629-7617 for a free estimate.
We identify the door series from the model label or by measurement, then source OEM or a verified equivalent through our authorized manufacturer lines – we’re an authorized installer for more than a dozen lines including Andersen, Pella, Marvin, Milgard, PGT, CGI, and ES Windows. For CWS-specific hardware we match the part number to the series spec before ordering. TruePane Windows & Doors Enterprise is an independent service provider and is not affiliated with CWS. Call (844) 629-7617 to get a quote started.
Standing offers: $50 Off Any Repair Over $250, an $89 Seasonal Tune-Up, and a permanent 5% discount for seniors and veterans. A live person answers the phone 24 hours a day, 7 days a week. Our technicians have up to 18 years of experience.
If your CWS door is dragging, not latching, or fogging between the panes, the fix is usually simpler and less expensive than you expect. A square deal, quoted on paper, done right the first time – that’s the standard we hold on every job in Enterprise and the surrounding neighborhoods. Call (844) 629-7617 for a free estimate. We’ll measure the door twice, quote the part honestly, and stand behind the work in writing.
Written by the team at TruePane Windows & Doors Enterprise, serving Enterprise and nearby areas.