Sliding glass doors
Single hung
Double hung
Horizontal roller
Casement
Bay & bow
Entry doors
Impact garage doors
PGT
CGIFree in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Get your free estimateMr-Glass Custom Windows & Doors in Enterprise: What to Know First
We provide independent custom window and door work for Mr-Glass products in Enterprise, from a single failed seal to a full opening that needs a new frame and sash built to fit. Most custom orders take 4 to 8 weeks from final measure to install, depending on the series and finish; a repair on existing Mr-Glass glass usually happens in one visit. We’re not the cheapest bid you’ll get, and we don’t pretend to be. You’ll get a written line-item quote before anything is ordered, and a live person answers the phone at (844) 629-7617, day or night.
This page is for the homeowner who already has Mr-Glass products in the wall and wants them handled by someone who knows the line. As an independent Mr-Glass service provider, we are not affiliated with or authorized by Mr-Glass. What we know is the product in the field, here in Enterprise, in this climate.
How Mr-Glass Products Fail – and How We Fix Them
Mr-Glass builds to spec, and most of what we see on custom orders isn’t a manufacturing defect at all. It’s installation and site conditions. These are the five we run into most in Enterprise.
- Seal failure and fogging in sealed units. The most common call we get. Desiccant saturates, the spacer fails, and moisture clouds the glass from the inside. On Mr-Glass fixed and casement units, the tell is a fog band that starts at the bottom edge and climbs. There’s no cleaning it out; the insulated unit gets replaced, and we match the original glazing spec so the sightline stays right.
- Frame and sash binding in summer heat. Nevada summers push vinyl and thermally broken aluminum through real expansion. A Mr-Glass slider or hung window that opened fine in April drags in July because the frame set slightly out of square or the installer shimmed it tight to one corner. We re-plumb the frame, correct the shimming, and adjust the hardware rather than forcing it.
- Sun-baked weatherstrip and gaskets. Our UV load breaks down glazing gaskets and sweep seals years before the glass fails. You’ll notice a draft or a whistle at the latch side. We replace the gasket with the correct profile, which matters because the wrong durometer either seals too hard or not at all.
- Failed hardware and operators on custom units. Multi-point locks, tilt-latch mechanisms, and awning operators wear. Aftermarket parts often fit but don’t sit right. We pull up the OEM part and show you the aftermarket option side by side, so you’re choosing with your eyes open on both cost and fit.
- Water intrusion at the sill on doors and low windows. This is where custom work earns its keep. On Enterprise doors, a sill that wasn’t set with a proper slope and backer rod lets wind-driven rain track in during monsoon season. We diagnose the flashing and sill detail, not just the door, because a new door over a bad sill fails the same way.
Here’s a detail that surprises owners: on some Mr-Glass units the fogging starts only on north-facing glass, because that side sees wider temperature swings than the sun-baked south wall. If the fog is one-sided, that’s usually the reason, and it confirms the insulated unit and not the frame.
Styles & brands we work with
- Single hung
- Double hung
- Horizontal roller
- Casement
- Bay & bow
- Sliding glass doors
- Entry doors
- Impact garage doors
- PGT
- CGI
Our Mr-Glass Custom Windows & Doors Process
- 1
The call. A live person answers, day or night. We ask what the product is, what it’s doing, and when it started. No voicemail tree, no callback form.
- 2
In-home diagnostics. A background-checked, uniformed technician measures every opening twice, checks the frame for square, tests the hardware, and looks at the sill and flashing. We tell you what we find, plainly.
- 3
The parts decision. For repairs, we lay out the OEM part and a quality aftermarket option on paper, with the trade-off in fit and price. For custom orders, we quote more than a dozen manufacturer lines side by side so you see exactly what you’re buying.
- 4
The work. Most repairs finish in one visit. Custom installs are scheduled, sequenced, and done by technicians who’ve worked the line before. We set the sill right, shim correctly, and seal it to shed water.
- 5
The test. Every unit gets operated through its full range, and we check for draft, binding, and water path before we call it done.
- 6
The guarantee. The Keystone Standard means both manufacturer warranty layers are registered in writing, with durations stated, before the truck leaves the driveway. Plus our 90-Day Done Right Promise: if it isn’t right, we make it right, no paperwork fight.
See the difference
Before
After
Before
After
Before
AfterWhat Mr-Glass Custom Windows & Doors Costs in Enterprise
Prices here reflect the Enterprise market and what the work actually involves. Every quote is written and itemized up front, and it doesn’t change once work starts.
| Job | Typical range |
|---|---|
| Replacement insulated glass unit (fogged seal) | $220 – $480 |
| Weatherstrip / gasket replacement per opening | $95 – $220 |
| Hardware or operator repair | $140 – $380 |
| Custom sash or frame build to fit existing opening | $650 – $1,900 |
| Full custom window or door, supplied and installed | $1,400 – $5,500+ |
What moves the price: the Mr-Glass series, glass type (impact and low-E cost more), finish, and whether the frame or sill has to be corrected. A repair over $250 takes $50 off, and we keep a permanent 5% discount for seniors and veterans. Call (844) 629-7617 for a free estimate – the number is the estimate, not a sales visit.
Why Enterprise Homeowners Call TruePane Windows & Doors Enterprise for Mr-Glass Work
We’ve proudly served local communities for over 42 years, and our technicians have up to 18 years of experience on the tools. We know how Mr-Glass products were set in Enterprise homes and how they hold up to our heat and dust. When a part needs to come from the manufacturer line, we also install and service PGT, CGI, CWS, and ES Windows, so a delayed or discontinued Mr-Glass component doesn’t leave you stuck.
What you get on every job: a square deal with upfront pricing, technicians who measure twice and show up when we say, and a company that still answers the phone if something goes wrong a year from now. We’re local, we hire local, and we train apprentices into journeymen. We stand behind the work, the warranty, and the promise, in writing. And our founding rule hasn’t changed: if the pane is not true, the job is not done.
FAQs
No, when it’s done correctly. The risk comes from improper installation or aftermarket parts that don’t meet spec, not from the work itself. We handle this with the Keystone Standard: both manufacturer warranty layers registered in writing, durations stated, before we leave. Call (844) 629-7617 and we’ll explain exactly what’s covered.
Usually, yes. Many Mr-Glass components are still available, and when one is discontinued we source a matched aftermarket part and show you the trade-off in fit and price before installing it. It’s rare that an owner has to replace a whole unit just because a part is hard to find. Call us for a free estimate on what your unit needs.
Repair if the frame and sill are sound and the problem is glass, gasket, or hardware. Replace when the frame is out of square, water is getting behind it, or multiple units are failing at once. We’ll tell you honestly which side of that line you’re on, because a good frame is worth keeping. Call (844) 629-7617 for a free estimate.
Most repairs finish in a single visit once we’ve seen the unit and confirmed the part. Custom orders take longer because the product is built to your opening, typically 4 to 8 weeks. We’ll give you a real date, not a guess. Call (844) 629-7617 to schedule.
Where the work requires it, yes. We handle the permitting and stand behind the inspection, and it’s priced into your written quote up front so there are no surprise line items. That’s part of doing it right the first time.
If you have Mr-Glass windows or doors in Enterprise that need a repair or a custom build, call TruePane Windows & Doors Enterprise at (844) 629-7617 for a free estimate. A live person will answer, we’ll come measure, and you’ll get a written quote you can hold us to.
Written by the team at TruePane Windows & Doors Enterprise, serving Enterprise and nearby areas.