Sliding glass doors
Single hung
Double hung
Horizontal roller
Casement
Bay & bow
Entry doors
Impact garage doors
PGT
CGIFree in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Get your free estimateCWS Sliding & Patio Doors: The Enterprise Owner’s Guide
We install and service CWS-compatible sliding and patio doors in Enterprise, and a full door replacement with a CWS-spec unit typically runs $2,400 to $5,800 installed, depending on width, glass package, and frame color. Most single-door swaps are planned work, not emergency work, so we schedule them properly rather than promise same-day.
Owners usually find the problem the same way: the door stops latching cleanly, the roller drags on the track, or a fogged pane shows up after a summer. In Enterprise, the failure rarely announces itself. It creeps in over a season or two until the door that slid with one finger needs a shoulder behind it. That’s the point most people start looking for the right part.
Key Takeaways
- CWS sliding and patio doors use series-specific roller and track profiles that don’t swap between model lines.
- Installed pricing in Enterprise runs about $2,400 to $5,800 for a full door, and $180 to $420 for a roller or track repair.
- Nevada’s dust and summer heat wear out rollers and weatherstripping faster than in milder climates.
- We’re an independent service provider, not affiliated with CWS, and we quote manufacturer lines side by side on paper.
Which CWS Models This Applies To
CWS builds several sliding and patio door lines, and the parts are not interchangeable across them. The roller assembly that fits a narrow two-panel slider is a different profile from the one in a wide three-panel unit, and the differences are small enough to fool a tape measure. The reliable way to identify your door is to read the label on the frame or glass spacer and write down the series, the panel width, and the panel height before you call anyone. When the label is gone, which happens on older doors in Enterprise, we measure the opening and the roller track profile directly.
At that point you have a real decision: OEM part or quality aftermarket equivalent. For CWS doors still under manufacturer coverage, an OEM roller or track section keeps that coverage intact, and we register the work so nothing gets voided. For doors past their coverage window, a well-matched aftermarket roller often costs less and lasts the same, as long as the profile and weight rating are correct. A roller rated for a 60-pound panel on a 90-pound door will flatten within a year. We check that spec before we quote, in Enterprise, rather than after the door starts dragging again.
Styles & brands we work with
- Single hung
- Double hung
- Horizontal roller
- Casement
- Bay & bow
- Sliding glass doors
- Entry doors
- Impact garage doors
- PGT
- CGI
Signs Your CWS Sliding & Patio Door Is Failing
The symptoms below are the ones we see most on CWS units around Enterprise. Each points to a specific part, which is what makes a proper diagnosis worth the visit.
- The door drags or needs a shoulder to slide. Worn or seized rollers are the usual cause; the nylon or steel wheels flatten and stop turning, so the panel skids along the track instead of rolling.
- You hear a grinding or scraping as it moves. Grit packed into the track is chewing at the roller and the bottom rail. In Nevada’s dusty summers, a track that goes a year without cleaning will wear a roller out early.
- The door won’t latch or seal at the top and bottom corners. The frame has shifted or the weatherstripping has hardened and shrunk, leaving a gap that lets hot air and dust straight through.
- A pane fogs or collects moisture between the glass. The seal in the insulated glass unit has failed; the glass itself needs replacing, not the frame, and that’s a job for a glazier rather than a roller swap.
- The track is bent, dented, or worn through. A damaged track will ruin a new roller in a matter of months, so the track has to be addressed along with the wheels, not after.
One honest note on timing: a worn roller is annoying, but a damaged track or a door that has come off its alignment can be a genuine lift hazard, and a heavy glass panel is not something to wrestle with on a step ladder. If the door is hard to lift or the panel rocks in the frame, stop forcing it and have it looked at.
Replacement Cost & What’s Included
Here’s the pricing picture we quote in Enterprise, with parts and labor shown together so there are no surprise line items on the bill.
| Work | Typical Installed Range |
|---|---|
| Roller replacement (per panel) | $180 – $320 |
| Track repair or replacement | $240 – $420 |
| Weatherstripping and seal refresh | $150 – $280 |
| Insulated glass unit (fogged pane) | $350 – $700 |
| Full CWS-compatible sliding/patio door | $2,400 – $5,800 |
What drives the range: panel width and weight, whether the track needs replacement alongside the rollers, the glass package, and frame color. We quote parts and labor separately so you can see exactly where the money goes, and we’re authorized installers for more than a dozen manufacturer lines, including Andersen, Pella, Marvin, Milgard, PGT, and CGI, so the side-by-side comparison is on paper. Every job carries the 90-Day Done Right Promise, and we register both manufacturer warranty layers in writing before we leave. Current offers include $50 Off Any Repair Over $250, an $89 Seasonal Tune-Up, and a permanent 5% discount for seniors and veterans.
See the difference
Before
After
Before
After
Before
AfterDIY or Call Us?
Some of this you can check safely yourself. Clean the track with a brush and vacuum, look for grit packed into the bottom rail, and note whether the rollers actually turn when you lift the panel slightly. If a roller spins freely and the track is clean, the problem may be alignment rather than a part.
Where DIY goes wrong is when the panel has to come out of the frame. A sliding glass panel on a patio door can weigh well over a hundred pounds, and lifting it out of a misaligned track without a second set of hands and the right technique is how backs get hurt and glass gets broken. Measuring a roller profile wrong is the other common miss: the part looks identical until it’s installed and the door still drags. Our technicians have up to 18 years of experience, measure every opening twice, and background-checked, uniformed technicians handle the heavy lifting. If you’ve checked the simple things and the door still fights you, call (844) 629-7617 for a free estimate.
FAQs
Expect seven to twelve years on a roller in this climate, and often less on a door facing full afternoon sun with dusty tracks. Nevada’s grit and summer heat break down the wheels faster than in milder regions, which is why yearly track cleaning stretches the part’s life considerably. We measure the roller profile directly rather than guessing from the door’s age, so the replacement actually fits.
Yes, in most cases, and we’d rather fix the part than sell you a door you don’t need. Rollers, tracks, weatherstripping, and a fogged glass unit can all be replaced on their own, and only a warped frame or a failed structural panel usually pushes toward a full replacement. When we look at your CWS door in Enterprise, we’ll tell you plainly which side of that line you’re on.
A roller or track repair is typically a single visit, often done the same day we assess it, and most of our jobs are completed in one trip. A full door replacement is scheduled planned work, since the unit has to be ordered to your measurements and glass package. We’ll give you a realistic window up front rather than a promise we can’t keep.
We match your CWS series and panel dimensions to the correct roller or track profile, then quote the OEM part and a quality aftermarket equivalent side by side on paper. We don’t claim to stock parts or carry them on a truck; we order the right part for your door and confirm the weight rating before installation. That way you see exactly what you’re buying and what it costs.
Get Your CWS Door Sliding Right Again
If your CWS sliding or patio door has started dragging, fogging, or refusing to latch, we’ll come out, measure the opening twice, and give you a straight answer on whether it’s a part or a replacement. A live person answers the phone 24 hours a day, seven days a week, and we’ll be there when we say. Call (844) 629-7617 for a free estimate in Enterprise, and we’ll put the numbers in writing before any work starts. We also service PGT, CGI, and ES Windows, so whatever’s in your wall, bring it up when you call.
Written by the team at TruePane Windows & Doors Enterprise, serving Enterprise and nearby areas.