Impact garage doors
Single hung
Double hung
Horizontal roller
Casement
Bay & bow
Sliding glass doors
Entry doors
PGT
CGIFree in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Get your free estimateCGI Impact Garage Doors: The Enterprise Owner’s Guide
We install CGI-compatible impact garage doors and replacement components for Enterprise homeowners, and a full door swap with impact-rated panels typically lands between $2,400 and $6,800 installed, with component-level repairs running $180 to $650. Most Enterprise owners don’t call us because the door stopped working overnight. They call because the door started sounding wrong in July, or because a panel took a hit from a garbage can and the dent never sat right again, or because the opener strains louder every summer until the neighbor finally mentions it.
Wind-borne debris is the usual culprit here. Enterprise sits close to open desert, and the same gusts that push dust under a door seal also drive gravel and palm fronds into impact panels. When a CGI door reaches that point, you’re not shopping for a look. You’re matching a part to a model so the door still meets impact rating and still closes square.
Which CGI Models This Applies To
CGI makes impact garage doors and hurricane-rated entry systems, and the garage door line is built to Florida and coastal wind-load standards that translate well to Southern Nevada’s wind events. The models most common on Enterprise homes are the CGI impact sectional door series sold through authorized dealers, and the part you need depends on which series and width you have. CGI doors are typically stamped with a data label inside the jamb or on the top section, and that label carries the model code, the design pressure rating, and the panel thickness. Photograph it before you call anyone. That label is the difference between a correct part and a second visit.
Here’s the compatibility gotcha that catches most owners: CGI impact panels are matched by track radius and hinge placement, not by door width alone. A 16-foot door from one CGI series will not accept the roller and hinge set from another series, even though the panel looks identical on the outside. That’s why we measure the opening and check the label rather than trusting the tape measure alone.
On the OEM-versus-aftermarket question, our honest position is that OEM is right for structural panels and hinges, and a quality aftermarket equivalent is fine for rollers, weatherseal, and bottom astragal. We quote both lines side by side on paper so you see the price and the spec difference before you decide. TruePane Windows & Doors Enterprise is an independent service provider and is not affiliated with CGI.
Styles & brands we work with
- Single hung
- Double hung
- Horizontal roller
- Casement
- Bay & bow
- Sliding glass doors
- Entry doors
- Impact garage doors
- PGT
- CGI
Signs Your CGI Impact Garage Doors Is Failing
Impact doors fail at the seals and hardware long before the panel itself gives out. Here’s what Enterprise owners describe to us, and what’s usually behind it.
- The door slams or shudders near the floor. A worn bottom astragal or a bent track lets the door ride off-square, and the panel catches the jamb on the way down. Left alone, that catches the hinge next.
- Visible daylight or dust streaks along one side. Weatherseal in Southern Nevada dries and cracks faster than most owners expect, because the summer heat and low humidity pull the flexibility out of the vinyl. Once a seal goes hard, grit gets in and the gap widens.
- The opener runs louder every summer. Heat-thinned lubricant and a stretched torsion spring both show up as sound first. If the noise climbed over a season or two, the spring is a likely suspect.
- A panel is dented or the door no longer meets rating. An impact door that has taken a hard hit may still open, but the panel’s rating is compromised. That matters for insurance and for code.
- Rust or white corrosion at the hinges and fasteners. Monsoon-season moisture and irrigation overspray get into the metal, and the hinge pins seize. Seized pins put strain on the opener and the panels.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
On a typical Enterprise home, here’s what the numbers look like. Every quote we write is line-itemed, and the price you sign is the price you pay. No change orders, no surprise add-ons on the bill.
| Item | Typical Installed Range |
|---|---|
| Bottom astragal and weatherseal replacement | $180 – $340 |
| Hinge and roller set replacement | $240 – $480 |
| Torsion spring replacement (both springs) | $320 – $650 |
| Single impact-rated panel replacement | $550 – $1,400 |
| Full CGI-compatible impact door, installed | $2,400 – $6,800 |
The range depends on door width, panel count, whether the existing track is reusable, and whether the opener needs to come out to reach the hardware. Everything is quoted up front, and most jobs finish in a single visit. Every replacement carries our 90-Day Done Right Promise: if a seal leaks or a hinge binds, we come back and make it right. No arguing, no fine print.
DIY or Call Us?
Be straightforward with yourself about the split. You can safely check the data label, look at the weatherseal for cracks, and watch the door cycle with the opener disconnected to hear where the noise is coming from. You can vacuum grit out of the track and tighten a loose hinge screw that’s already finger-loose.
What you shouldn’t touch is the torsion spring. That’s a high-tension steel coil under hundreds of pounds of load, and a spring that lets go while you’re on a ladder will do serious damage. The same goes for any adjustment to the cables or the track geometry. Safety isn’t the only reason to stop there. An impact door has to close to its rated position, and a home adjustment that looks square can void the rating and the warranty. That’s work for a trained technician with the right tools, not a Saturday project.
For anything past a visual check, call us at (844) 629-7617. We’ll tell you on the phone whether it sounds like a component or a full door.
FAQs
How long do CGI impact garage door components last in Enterprise?
Plan on weatherseal and the bottom astragal every four to six years in Enterprise’s climate, and torsion springs every seven to ten years depending on how many times the door cycles a day. The door panels themselves last much longer if the hardware and seals are maintained.
Can my part be repaired instead of replaced?
Usually yes, and we’ll say so if it’s true. A sagging door with a good spring often just needs hinges and a track adjustment. A door that took a hard hit on one panel usually needs the panel replaced, not the whole door. You’ll get a straight answer on what repair does and doesn’t fix.
How long does the swap take?
A in the same day for seals, hinges, and rollers, and about four to six hours for a full impact door replacement. We confirm the window when we quote so you can plan around it.
How do you source the part?
We order directly from CGI authorized suppliers using the model code off your door’s data label. We confirm the part number against your label before ordering, so what arrives is what fits. If a part is backordered, we tell you the lead time up front rather than after your door is already disassembled.
Call (844) 629-7617 to schedule your free estimate on any CGI impact garage door in Enterprise. A live person answers every call, day or night. We’ll measure the opening, read the label with you, and quote the part you actually need.
Written by the team at TruePane Windows & Doors Enterprise, serving Enterprise and nearby areas.